Proxmark3 community

Research, development and trades concerning the powerful Proxmark3 device.

Remember; sharing is caring. Bring something back to the community.


"Learn the tools of the trade the hard way." +Fravia

  • Logged in as ikarus
  • Last visit: Today 11:22:42

Announcement

Time changes and with it the technology
Proxmark3 @ discord

Users of this forum, please be aware that information stored on this site is not private.

#1 2009-07-14 21:50:44

wilder
Member
Registered: 2009-06-21
Posts: 6

hi14read does not work

I have probably the stupid problem, but I didn't find a solution in this forum.

it doesn't matter if I put my mifare card near antenna or not, hi14read always returns me :

#db# 00000003, 00000000, ffffffff

hi14alist shows no activity

but according to 'tune', I can detect this card:

(without card):
> tune
# LF antenna @  23 mA / 29438 mV [1273 ohms] 125Khz
# LF antenna @  23 mA / 28249 mV [1187 ohms] 134Khz
# HF antenna @ 151 mA / 13640 mV [90 ohms] 13.56Mhz

(with card):

> tune
# LF antenna @  22 mA / 29192 mV [1273 ohms] 125Khz
# LF antenna @  23 mA / 28249 mV [1187 ohms] 134Khz
# HF antenna @ 128 mA / 11550 mV [90 ohms] 13.56Mhz

loread seems to work without problem (I can read my HID ProxyCard II)

Where is the problem?

I tried original firmware from 3.1.2009, pm3-20090603-r29 and pm3-20090713-r52, but the same problem.

Offline

#2 2009-07-14 22:03:08

d18c7db
Contributor
Registered: 2008-08-19
Posts: 292

Re: hi14read does not work

You seem to be mixing commands for different protocols, like hi14read (which is ISO-14443-B) with hi14alist (ISO-14443-A). Try hi14areader maybe prior to hi14alist. Also read the manual.

Offline

#3 2009-07-14 22:31:04

wilder
Member
Registered: 2009-06-21
Posts: 6

Re: hi14read does not work

Of course firstly I tried to use hi14areader, but it returned me:
#db# uknown command

I tried pm3-20090713-r52 and pm3-20090603-r29 firmware.
And my original firmware from 3.1.2009 does not support hi14areader (I don't see it in 'help').

Probably this is related with the fact, that I had problem to flash recent fpga-image.s19 (because after that my device stops working). I have no problem with the flashing recent bootrom.s19 and osimage.s19.

Any ideas?

Thanks,

Pavol

d18c7db wrote:

You seem to be mixing commands for different protocols, like hi14read (which is ISO-14443-B) with hi14alist (ISO-14443-A). Try hi14areader maybe prior to hi14alist. Also read the manual.

Offline

#4 2009-07-14 22:41:30

wilder
Member
Registered: 2009-06-21
Posts: 6

Re: hi14read does not work

Yes, so it was related with this problem http://www.proxmark.org/forum/topic/274 … aimages19/

I successfully flashed the recent fpga firmware, and now it works.

Anyway, thanks a lot.

Pavol

Offline

Quick reply

Write your message and submit

Board footer

Powered by FluxBB