Research, development and trades concerning the powerful Proxmark3 device.
Remember; sharing is caring. Bring something back to the community.
"Learn the tools of the trade the hard way." +Fravia
Time changes and with it the technology
Proxmark3 @ discord
Users of this forum, please be aware that information stored on this site is not private.
Pages: 1
Hi everybody,
I have used pm3 with hf tag, yesterday i began with LF, then connected the antenna and applied:
proxmark3> hw tune
the response:
Measuring antenna characteristics, please wait.........
# LF antenna: 7.56 V @ 125.00 kHz
# LF antenna: 10.31 V @ 134.00 kHz
# LF optimal: 14.99 V @ 139.53 kHz
# HF antenna: 0.85 V @ 13.56 MHz
# Your HF antenna is unusable.
Displaying LF tuning graph. Divisor 89 is 134khz, 95 is 125khz.
proxmark3> X Error: BadAccess (attempt to access private resource denied) 10
Extension: 130 (MIT-SHM)
Minor opcode: 1 (X_ShmAttach)
Resource id: 0x145
X Error: BadShmSeg (invalid shared segment parameter) 128
Extension: 130 (MIT-SHM)
Minor opcode: 5 (X_ShmCreatePixmap)
Resource id: 0x2c00010
X Error: BadDrawable (invalid Pixmap or Window parameter) 9
Major opcode: 62 (X_CopyArea)
Resource id: 0x2c00011
X Error: BadDrawable (invalid Pixmap or Window parameter) 9
Major opcode: 62 (X_CopyArea)
Resource id: 0x2c00011
X Error: BadAccess (attempt to access private resource denied) 10
Extension: 130 (MIT-SHM)
Minor opcode: 1 (X_ShmAttach)
Resource id: 0x145
X Error: BadShmSeg (invalid shared segment parameter) 128
Extension: 130 (MIT-SHM)
Minor opcode: 5 (X_ShmCreatePixmap)
Resource id: 0x2c00012
X Error: BadDrawable (invalid Pixmap or Window parameter) 9
Major opcode: 62 (X_CopyArea)
Resource id: 0x2c00013
X Error: BadDrawable (invalid Pixmap or Window parameter) 9
Major opcode: 62 (X_CopyArea)
Resource id: 0x2c00011
X Error: BadDrawable (invalid Pixmap or Window parameter) 9
Major opcode: 62 (X_CopyArea)
Resource id: 0x2c00013
Any idea?
Thanks.
Last edited by sfl (2018-01-25 16:39:23)
Thanks @iceman.
>sudo uname -a
Linux kali 4.14.0-kali1-amd64 #1 SMP Debian 4.14.2-1kali1 (2017-12-04) x86_64 GNU/Linux
Prox/RFID mark3 RFID instrument
bootrom: master/v3.0.1-268-g138a0e7-suspect 2018-01-16 15:11:28
os: master/v3.0.1-268-g138a0e7-suspect 2018-01-16 15:11:29
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2017/10/27 at 08:30:59
uC: AT91SAM7S512 Rev B
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 512K bytes. Used: 197809 bytes (38%). Free: 326479 bytes (62%).
Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory
To install i used: https://github.com/Proxmark/proxmark3/wiki/Kali-Linux and all fine with HF
Last edited by sfl (2018-01-24 16:43:10)
@iceman, you are a MVP !!!
I followed your recomendation:
1. I upgraded QT from 4.8.2 to 5.10.
2. Also, was necessary compiling the PM3 firmware again.
PM3 ready !!!
Thanks a lot.
Last edited by sfl (2018-01-25 18:18:39)