Proxmark3 community

addy

Contributor

Registered: 2016-09-19

Posts: 16

Error creating dump file

When I run the command  hf mf dump I get an error message and no output file is written

|-----------------------------------------|
|------ Reading sector access bits...-----|
|-----------------------------------------|
#db# READ BLOCK FINISHED
#db# READ BLOCK FINISHED
#db# READ BLOCK FINISHED
#db# READ BLOCK FINISHED
#db# READ BLOCK FINISHED
#db# Multiple tags detected. Collision after Bit 27
#db# Can't select card
#db# READ BLOCK FINISHED
Could not get access rights for sector  5. Trying with defaults...
#db# READ BLOCK FINISHED
#db# READ BLOCK FINISHED
#db# Cmd CRC response error.
#db# Read block error
#db# READ BLOCK FINISHED
Could not get access rights for sector  8. Trying with defaults...
#db# READ BLOCK FINISHED
#db# Cmd CRC response error.
#db# Read block error
#db# READ BLOCK FINISHED
Could not get access rights for sector 10. Trying with defaults...
#db# Cmd CRC response error.
#db# Read block error
#db# READ BLOCK FINISHED
Could not get access rights for sector 11. Trying with defaults...
#db# Can't select card
#db# READ BLOCK FINISHED
Could not get access rights for sector 12. Trying with defaults...
#db# READ BLOCK FINISHED
#db# READ BLOCK FINISHED
#db# READ BLOCK FINISHED
|-----------------------------------------|
|----- Dumping all blocks to file... -----|
|-----------------------------------------|
#db# READ BLOCK FINISHED
Successfully read block  0 of sector  0.
#db# READ BLOCK FINISHED
Successfully read block  1 of sector  0.
#db# Authentication failed. Card timeout.
#db# Auth error
#db# READ BLOCK FINISHED
Could not read block  2 of sector  0

I have all my keys:

proxmark3> hf mf ekeyprn
|---|----------------|----------------|
|sec|key A           |key B           |
|---|----------------|----------------|
|000|  ffffffffffff  |  cb352c149e36  |
|001|  32a60f82f087  |  cb352c149e36  |
|002|  ffffffffffff  |  ffffffffffff  |
|003|  ffffffffffff  |  ffffffffffff  |
|004|  ffffffffffff  |  ffffffffffff  |
|005|  ffffffffffff  |  ffffffffffff  |
|006|  ffffffffffff  |  ffffffffffff  |
|007|  ffffffffffff  |  ffffffffffff  |
|008|  ffffffffffff  |  ffffffffffff  |
|009|  ffffffffffff  |  ffffffffffff  |
|010|  ffffffffffff  |  ffffffffffff  |
|011|  ffffffffffff  |  ffffffffffff  |
|012|  ffffffffffff  |  ffffffffffff  |
|013|  ffffffffffff  |  ffffffffffff  |
|014|  ffffffffffff  |  ffffffffffff  |
|015|  ffffffffffff  |  ffffffffffff  |
|---|----------------|----------------|

After a few tries with the read sector command, I can read each sector

proxmark3> hf mf rdsc 0 A FFFFFFFFFFFF
--sector no:0 key type:A key:ff ff ff ff ff ff

#db# Authentication failed. Error card response.
#db# Auth error
#db# READ SECTOR FINISHED
isOk:00
proxmark3> hf mf rdsc 0 A FFFFFFFFFFFF
--sector no:0 key type:A key:ff ff ff ff ff ff

#db# Cmd Error: 04
#db# Read sector  0 block  2 error
#db# halt error. response len: 1
#db# Halt error
#db# READ SECTOR FINISHED
isOk:00
proxmark3> hf mf rdsc 0 A FFFFFFFFFFFF
--sector no:0 key type:A key:ff ff ff ff ff ff

#db# READ SECTOR FINISHED
isOk:01
data   : 46 b9 8f 95 e5 88 04 00 c0 8e 1a 19 55 70 14 12
data   : 70 69 81 00 30 12 72 91 24 d5 91 27 22 15 30 00
data   : 01 56 a7 75 ce 9a 04 0d fe 44 d0 7d 95 1e bb 7a
trailer: 00 00 00 00 00 00 48 77 8b 00 00 00 00 00 00 00

Could I have a bad proxmark?

Can I create the output file manually? I would manually read each sector then copy/paste it in the notepad editor.  What would be the format of this file and how would it be organized?

As a check:

Prox/RFID mark3 RFID instrument
bootrom: master/v2.2.0-271-g910ad54-dirty-suspect 2016-12-19 18:01:16
os: master/v2.2.0-271-g910ad54-dirty-suspect 2016-12-19 18:01:22
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/11/ 2 at  9: 8: 8

uC: AT91SAM7S256 Rev C
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 256K bytes. Used: 185695 bytes (71). Free: 76449 bytes (29).

Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory
proxmark3>

Thanks for you help

iceman

Administrator

Registered: 2013-04-25

Posts: 9,468

Website

Re: Error creating dump file

Could be antenna, run and paste yr output.

 hw tune 

It could also be the positioning of tag and antenna, usually 1-1.5cm is a good distance.  trial and error to find the sweet spot.

Not sure why u use "ekeyprn".

Read the datasheet for mifare classic to see the memory layout.

addy

Contributor

Registered: 2016-09-19

Posts: 16

Re: Error creating dump file

Thanks iceman.

here is my ant details

proxmark3> hw tune

Measuring antenna characteristics, please wait........
# LF antenna: 31.21 V @   125.00 kHz
# LF antenna: 29.15 V @   134.00 kHz
# LF optimal: 36.16 V @   129.03 kHz
# HF antenna: 28.50 V @    13.56 MHz
Displaying LF tuning graph. Divisor 89 is 134khz, 95 is 125khz.

addy

Contributor

Registered: 2016-09-19

Posts: 16

Re: Error creating dump file

Got it to work.

1. removed lf ant
2. held it a small distance from the reader.

thanks iceman for your help

iceman

Administrator

Registered: 2013-04-25

Posts: 9,468

Website

Re: Error creating dump file

You should not have to remove the lf antenna,  well, there are posts about the pm3 version from Elechouse, "pm3 easy".